1. Cut a length of beading thread, leaving a tail for knotting. Thread on a needle.
2. Pick up a flat bead and pass the needle through the hole from back to front.
Pull the thread until the bead sits snugly against the preceding bead, then make a knot close to the bead to secure it in place. Repeat with additional beads until you have reached your desired bracelet length.
3. To finish, pass the needle through the final few beads again and make a double knot at the end of the thread tail.
Trim any excess thread.
- Decide on the length of your bracelet
- Cut a length of beading wire that is about 2 inches longer than the desired finished length of your bracelet
- String a crimp bead onto the end of the beading wire, then thread the beading wire back through the crimp bead
- Pull the beading wire until the crimp bead is snug against the beads, then use pliers to squeeze the crimp bead closed
- Begin stringing your beads onto the beading wire
- To make a flat bead bracelet, you will need to string two beads side-by-side for each “unit” of beads
- For example, if you are using 6mm round beads, you would string two together and then add another unit of two 6mm beads until you have reached your desired length
- Once you have reached your desired length, add a second crimp bead and secure it in place as described in Step 2 above
- Cut off any excess beading wire, leaving about 1/2 inch to work with
- Use flush cutters or Wire Snips to snip off any excess wire sticking out from behind the crimped area (this could potentially scratch someone if left sharp)
How to Make DIY Clay Bead Bracelets | The Pretty Life Girls
How to Make Bracelets With Beads Step by Step
Making bracelets with beads is a fun and easy craft that you can do at home. With just a few supplies, you can make beautiful bracelets to wear or give as gifts. Here’s what you need to get started:
Supplies:
-Beads (I like to use glass beads because they are pretty and come in a variety of colors)
-String or beading wire (I prefer using beading wire because it is stronger and less likely to break)
-Scissors
-A ruler or tape measure
Instructions:
1. Start by measuring out how much string or beading wire you will need for your bracelet. Cut the string/wire to the desired length, allowing for about an extra inch so that you can secure the ends later on.
2. Next, thread your beads onto the string/wire.
You can create any pattern or design that you like – there are no rules! Just have fun with it.
3. Once all of your beads are on the string/wire, double check the measurements to make sure your bracelet will fit snugly around your wrist.
If it’s too loose, add more beads; if it’s too tight, remove some beads.
4. To finish off the bracelet, tie a knot at each end of the string/wire (make sure it’s tight so that your beads don’t fall off). You can then trim away any excess string/wire.
Credit: www.youtube.com
How Many Flat Beads Make a Bracelet?
How many flat beads make a bracelet? It depends on the size of the beads and the desired length of the bracelet. For example, if you are using 6mm beads and want a 7-inch long bracelet, you will need approximately 84 beads.
How Do You Finish a Flat Bead Bracelet?
Assuming you mean how to end a bracelet with beads:
There are a few ways to finish off a bracelet with beads. One way is to thread the end of the beading wire through a bead, and then make a loop.
You can then use pliers to twist the wire around itself until it is secure. Another way is to thread the wire back through several beads, and then make a knot. Once again, use pliers to pull the knot tight and trim any excess wire.
How Do You Connect Flat Beads?
There are a few ways to connect flat beads, the most common being using jump rings. To attach a flat bead to a jump ring, first open the jump ring by twisting it to the side. Next, thread the jump ring through the hole in the bead and then twist the jump ring back closed.
You can also use other jewelry findings such as split rings or lobster clasps to connect flat beads. If you’re using split rings, simply open up the ring and thread it through the bead hole before closing it back up. For lobster clasps, open up the clasp and hook one end through the bead hole before closing it back up.
How Do You Make a Disc Bead Bracelet?
Disc bead bracelets are a fun and easy way to add some style to your wardrobe. They are also a great way to show off your personality and taste. Here is a step by step guide on how to make a disc bead bracelet:
1. Choose the beads you would like to use for your bracelet. You can use any type of beads, but disc beads work best because they lay flat against the wrist and don’t roll around.
2. String the beads onto beading wire or stretchy cord, using a needle if necessary.
Make sure that the string is long enough to fit comfortably around your wrist with room to spare.
3. Once all of the beads are strung, tie the two ends of the string together securely, making sure that there is no slack in the bracelet. Trim away any excess string.
4. Put the bracelet on and enjoy!
Conclusion
This blog post provides clear instructions on how to make a flat bead bracelet. It is easy to follow and makes a great beginner project. With just a few supplies, you can have a beautiful new bracelet in no time.
