1. String your needle with beading thread, and knot the end.
2. Pick up a shell bead, and thread it onto the needle.
3. Repeat step 2 until you have the desired number of beads on the strand.
4. To finish, knot the thread securely, and trim any excess.
- Start with the end of the string that has the larger bead on it
- This will be the end you thread through the other beads
- Pick up a shell bead and slide it down to the end of the string
- Cross the string over itself, making an “X”
- Take the top string (the one closest to your fingers) and put it over the “X” you just made
- Now poke it underneath both pieces of string, and pull up gently until tight against the shell bead
- The cross should now be snug against the hole in the center of the shell bead
- 5 Repeat steps 2-4 until all desired shell beads are strung onto cord
Credit: www.wikihow.com
How Do You Put Shell Beads in Braids?
If you’re looking to add a little something extra to your braids, shell beads are the perfect way to do it! Here’s how to put shell beads in braids:
1. Start with clean, dry hair that’s free of any oils or products.
This will help the beads stay in place better.
2. Decide which braid(s) you want to add beads to and gather them into a small section.
3. Using a needle and thread (or beading wire), string the beads onto the thread/wire.
The number of beads you’ll need will depend on the size of your braid and how many beads you want per inch.
4. Once all the beads are strung, carefully slide them down towards the end of the thread/wire so they’re close together. This will make it easier to attach them to your braid later on.
5. Take one of the strands from your braid and thread it through the loop at the end of the thread/wire (leaving a few inches of slack). Then pull tight so that strand is now holding all the beads in place against your braid base. Repeat this step with each strand until all strands are secure and there are no loose ends sticking out anywhere.
How Do You Put on a Shell Necklace?
Assuming you would like a step-by-step guide on how to put on a shell necklace:
1. Start by untangling the necklace if it is knotted. You can use your fingers or a pair of scissors to carefully snip any knots out.
2. Place the necklace around your neck. The clasp should be at the back of your neck.
3. Use one hand to hold the end of the necklace with the clasp and use your other hand to feed the rest of the necklace through the loop created by the first hand until it forms a complete circle.
The two ends of the necklace should now be attached together by the clasp.
How Do You Put Shells on Dreads?
If you’re looking to add shells to your dreads, there are a few things you’ll need to do first. First, make sure your dreads are fully matured and locked before attempting to add any shells. Otherwise, they may fall out.
You’ll also want to clean the shells thoroughly before adding them, as dirt and grime can cause buildup in your dreads. To attach the shells, simply thread them onto a piece of string or dental floss and tie them securely around the base of your dread. Start with just a few and see how they feel before adding more.
How Do You Attach a Shell to a Bracelet?
There are a few ways to attach shells to bracelets. The first way is to simply glue the shell onto the bracelet. This works best with small shells.
The second way is to wire wrap the shell onto the bracelet. This method is more secure and will keep the shell from falling off. First, you will need to create a small loop at the end of your wire.
Then, thread the wire through the hole in the shell and back through the loop. Pull tight and repeat on the other side of the shell. The third way is to sew the shell onto the bracelet.
You will need a needle and thread for this method. First, thread your needle and tie a knot at one end. Then, poke holes through both sides of the shell and thread your needle through both holes.
Tie a knot on each side of theshell to secure it in place.
How To: Add Beads & Shells To Braids and Twists
How to Put Shells on Natural Hair
If you’re looking for a way to add some extra flair to your natural hair, putting shells on it is a great option! Here’s how to do it:
1. Start with clean, dry hair.
If your hair is wet or even damp, the shells won’t stick as well.
2. Decide where you want to place the shells. You can put them all over your head, or just in certain sections.
Once you know where you want them, use a comb to make small partings in your hair so that the shells will have something to grip onto.
3. Put a small amount of glue on each shell. You can use regular craft glue or specially-made shell adhesive (available at most craft stores).
Then, press the shell into place on your hair and hold it there for a few seconds until the glue sets. Repeat with additional shells until you’re satisfied with the results!
Conclusion
In conclusion, shell beads are a beautiful and unique way to add style to any outfit. They are also easy to put on and take off, which makes them perfect for people who are always on the go.
